微机械谐振式硅桥传感器

本文描述了微机械谐振式硅桥传感器的工作原理,硅桥制作过程以及传感器的工作特性。讨论了传感系统的检测灵敏度与光纤头到硅桥表面距离的关系。实验结果表明,激励硅桥谐振的光功率是在10～450μW,探测信号的光功率在300μW时,其系统的信噪比为25～40dβ,它具有重要的实际应用价值。     

Thermomechanical and thermodilatometric analysis of green alumina porcelain

A modulated force thermomechanical analysis (mf-TMA) and thermodilatometric analysis (TDA) of the green ceramic mixture of kaolin (27 wt.%), Al₂O₃ (50 wt.%) and feldspar (23 wt.%) up to 1000 °C is presented. The mf-TMA reflects changes during heating the green ceramics with higher sensitivity than TDA. Discrepancies between mf-TMA and TDA revealed that the elastic behavior of the green porcelain samples is determined most importantly by processes on the crystal boundaries (escaping of the water molecules at the low temperatures up to 150 °C and solid state sintering at the temperatures above 450 °C). Processes in the crystal interiors (e.g. dehydroxylation) have a lesser function. Thermodilatometric results depend more on the processes which take place inside the crystals than on the processes on the crystal surfaces.     

Vibration fracture resistance of 5052H112 aluminum alloy processed by cold rolling and friction stirring

Hot-rolled Al–3Mg alloy processed by various cold-rolled reductions exhibited excellent vibration fracture resistance, however subsequent friction stirring did not endow better vibration fracture resistance than cold-rolled samples in spite of possessing microstructural refinement and homogenization. The D–N curve under a constant initial deflection amplitude (6.5 mm) also showed that the vibration fracture resistance of cold-rolled specimens increased as a result of the slower crack propagation rate. All samples used in this investigation showed a work hardening feature from the initial stage of the D–N curve, and the deflection amplitude tended to increase as the number of vibration cycles increased. During this ascending stage, slip band cracking and strain hardening in the vicinity of the main crack could be recognized. The D–N curve feature of the cold-rolled samples depicted a longer plateau region while the deflection amplitude was at its maximum. It is suggested that the dislocation tangles introduced by cold rolling can strengthen the matrix. As a result, the deflection amplitude drops could be associated with increasing the dislocation tangles due to prior cold rolling while the main crack achieved a critical crack length.     

高压电源的研究与分析

本文介绍了一种基于SG1525的高压电源的设计方案。本款高压电源主要利用了串联谐振变换原理进行设计。通过实验,此高压电源具有可靠、稳定、高效、功率密度高等优点。能满足中大功率机载雷达发射机的需要。     

Operation and control of a grid-connected DFIG-based wind turbine with series grid-side converter during network unbalance

This paper proposes a control scheme of a grid-connected doubly-fed induction generator (DFIG) wind turbine with series grid-side converter (SGSC) to improve the control and operation performance of DFIG system during network unbalance. The behaviors of DFIG system with SGSC under unbalanced grid voltage conditions are described. The SGSC is controlled to inject voltage in series to balance the stator voltage. Therefore, the adverse effects of voltage unbalance upon the DFIG such as large stator and rotor current unbalances, electromagnetic torque and power pulsations are removed and the conventional vector control strategy for the rotor-side converter (RSC) remains in full force under unbalanced conditions. Meanwhile, three selective control targets for the parallel grid-side converter (PGSC), such as eliminating the oscillations in total active or reactive power, or no negative-sequence current injected to the grid are identified and compared. Besides, the proportional resonant controllers in the stationary reference frame are designed for both the SGSC and PGSC to further improve the dynamic performance of the whole system. Finally, the ratings and losses of the SGSC and the injected transformer are discussed and the effectiveness of the proposed control scheme is verified by the simulation results of a 2 MW DFIG-based wind turbine with SGSC under steady state and small transient grid voltage unbalance.     

TD-LTE双频网结构规划研究

本文分析了TD-LTE系统F/D双频组网的必要性;分析了TD-LTE系统F/D双频组网的难点;分析了网络结构的调整对双频组网带来的影响;结合实际网络测试结果提出了合理的网络结构规划方案。     

热浸镀锌大型天线钢结构件的应用研究

热浸镀锌为大型天线的防腐蚀提供了解决方法,本文探讨了天线热浸镀锌存在的问题,并从修改天线结构形式等方面提出了改进的方案,实现了大型天线的热浸镀锌。     

RFID标签引脚阻抗的建模与计算

射频识别(RFID)标签的封装中,芯片与天线靠各向异性导电胶(ACA)连接。ACA的性质导致了芯片的引脚与天线连接处会有较大的阻抗,影响了标签的电参数,会对标签读写距离产生不利的影响。分析了芯片引脚处阻抗对标签的电性能的影响,对该处电阻与寄生电容进行了建模和计算。最后,依据理论计算了一款天线的引脚阻抗,并据此对该天线进行了优化与测试,验证了理论的正确性。     

TDM-PON上行信号光功率均衡器的锁模特性

为了减小时分复用无源光网络（TDM-PON）上行信号光波长的飘移,基于TDM-PON上行信号光功率均衡器架构,采用单模激光注入锁定光网络单元（ONU）法布里-珀罗（F-P）激光器（LD）方法,研究了F-P LD输出光波长的锁模特性,包括锁模的范围、驱动电流对锁模特性的影响、锁模前后温度变化引起F-P LD光波长变化情况等。结果表明,当驱动电流为9mA时,F-P LD可被锁模的波长范围为0.38nm,大于ONU上行光波长因环境温度变化5℃而产生的波长位移量0.25nm,F-P LD被锁模可使ONU上行信号的光波长相同且稳定,降低光功率均衡后的噪声。     

应用菲涅耳原理计算ILS下滑台保护区

仪表着陆系统下滑信标天线是通过地面反射作用形成引导飞机着陆的下滑面引导信号,反射面的反射性能直接影响下滑面的信号质量,本文通过应用菲涅耳原理对下滑信标天线反射面保护区进行了计算,可作为下滑台保护区确定的参考。